asphalt
ChatGPTEstimate asphalt volume, short tons, stone base and a USD cost range for a rectangular area at a supplied asphalt depth.
baluster_count
ChatGPTEstimate baluster count from railing length, number of posts, post width, baluster width and specified spacing.
baluster_spacing
ChatGPTLay out baluster centers and outside spacing in up to ten railing sections with a fixed gap and baluster width.
board_and_batten_layout
ChatGPTLayout with equal gaps between battens, from a desired spacing or number of battens.
brick_calculator
ChatGPTBrick, mortar and sand estimate for a rectangular wall using Build24's 3/8-inch joint. Pick a brick preset or provide custom face width and height.
check_square
ChatGPTCompute the expected diagonal of a rectangle for comparing measured corner-to-corner distances.
concrete_block
ChatGPTConcrete block, mortar and sand estimate for a rectangular wall. Presets list the nominal block face width x height in inches.
concrete_post_holes
ChatGPTEstimate concrete volume and alternative bag counts for identical round holes containing round posts. Subtracts the round post volume. Requires hole diameter, round post diameter and fill depth.
concrete_walls
ChatGPTVolume and optional concrete cost for identical straight walls of uniform thickness. Length and height are feet in US mode and meters in metric; thickness is inches or centimeters.
cubic_yards_volume
ChatGPTVolume from rectangular length, width and depth or from a known area and depth.
decking_calculator
ChatGPTEstimate deck area and lineal feet with 10% waste using Build24's row-spacing calculation. Row spacing is the distance from one board row to the next, not the gap between boards.
drywall_sheetrock
ChatGPTDrywall sheets, screws, tape and joint compound for rectangular room walls, with optional ceiling and panel cost.
feet_inches
ChatGPTAdd or subtract two lengths given in feet and decimal inches or meters and centimeters.
framing_material_usage
ChatGPTEstimate studs, three plate runs and sheathing equivalents from wall dimensions, stud spacing, corners and intersecting partitions.
framing_stud_count
ChatGPTEstimate vertical studs and top and bottom plate boards for a straight wall, with one to three studs at each end.
gravel_quantity
ChatGPTEstimate volume and weight for gravel, rock, sand, topsoil or riprap. Accepts dimensions and depth, area and depth, or a known volume. Weight ranges use US short tons and Build24 material densities.
inch_fraction_decimal
ChatGPTConvert a mixed inch fraction to decimal inches and feet, or a decimal inch value to its nearest 1/64-inch mark.
paint_calculator
ChatGPTEstimate paint and primer for individual walls, a rectangular room or total surface area. Deducts entered doors and windows using Build24's allowances.
plywood_sheet_count
ChatGPTEstimate whole 4-by-8-foot sheets from a rectangular coverage area. Uses area and rounds up.
rake_wall_height
ChatGPTPeak height of a rake wall from horizontal plate length, lower height and pitch rise per 12.
rake_wall_two_heights
ChatGPTRake-wall pitch, sloped top plate length and stud positions and lengths from low and high wall heights.
roof_pitch_slope
ChatGPTConvert roof rise and run or an acute angle to pitch per 12, slope and angle.
roofing_area_material
ChatGPTRoofing area, squares, shingle bundles and felt rolls from the horizontal rectangular footprint and integer pitch rise per 12. Use one consistent pitch.
running_measurements
ChatGPTGenerate Build24's 100 equally spaced layout marks from a starting distance and interval.
soil
ChatGPTSoil volume, 0.75 cubic foot bags and dry, compacted and wet weight ranges in US short tons. Provide depth and a known area or rectangular dimensions.
stairs
ChatGPTCalculate rise, run, step count and stringer geometry for a standard or flush mount. Supply the measured total rise, known horizontal measurement and either step rise or step count.
tape_measurement_helper
ChatGPTFind the closest fractional mark on an inch tape, at 1/2 through 1/64 inch precision.
tile_calculator
ChatGPTTile and box quantity from floor or wall dimensions or known area. Takes tile size, joint spacing, optional box size and optional price basis.
triangle_base_hypotenuse
ChatGPTSolve a right triangle from its horizontal leg and hypotenuse, in the same length unit.
triangle_base_lower_angle
ChatGPTSolve a right triangle from the base and lower angle. Other sides use the same length unit.
triangle_base_rise
ChatGPTSolve a right triangle from its horizontal base and vertical rise, in the same length unit.
triangle_base_upper_angle
ChatGPTSolve a right triangle from the base and upper angle. Other sides use the same length unit.
triangle_hypotenuse_lower_angle
ChatGPTSolve a right triangle from the hypotenuse and lower angle. Other sides use the same length unit.
triangle_hypotenuse_upper_angle
ChatGPTSolve a right triangle from the hypotenuse and upper angle. Other sides use the same length unit.
triangle_rise_hypotenuse
ChatGPTSolve a right triangle from its vertical leg and hypotenuse, in the same length unit.
triangle_rise_lower_angle
ChatGPTSolve a right triangle from the rise and lower angle. Other sides use the same length unit.
triangle_rise_upper_angle
ChatGPTSolve a right triangle from the rise and upper angle. Other sides use the same length unit.
unit_converter
ChatGPTConvert between length units (in, ft, yd, mm, cm, m), area units (ft2, yd2, m2), or volume units (ft3, yd3, m3).